Online Courses

Discount Packages

Ethics, Laws and Rules

Live Webinars

Video Presentations

Courses by Provider


CED Monthly

Subscribe and get 20% off

Your name:

Your e-mail:




FB Twitter LinkedIn

Maryland Materials and Ethics 16 PDH Discount Package

PACKAGE NO: MD16T-02
PACKAGE PDH: 16
PACKAGE PRICE: $220.8
To buy the package, please click on:
Courses in this Package
COURSE TITLE: Coating Application and Inspection
COURSE NO: T03-001
COURSE PROVIDER: Gilbert Gedeon, P.E.
Coating Application and Inspection
Course Highlights

This online engineering PDH course presents the technologies, techniques, advantages and limitations, equipment, typical coating types involved, and safety considerations for each type of application method.

 

The choice of an application method depends on the type of coating to be applied, the type and size of surface to be coated, and governing environmental regulations. There are various methods of coating application, including brush application, roller application, conventional spray, high volume-low pressure spray, airless spray, plural component spray, and electrostatic spray.

 

Approximately 85 percent of all premature coating failures are a result of poor surface preparation, inadequate mixing, thinning, and/or poor coating application. Onsite quality control inspection during surface preparation and coating application procedures can help prevent failures of these types. Proper inspection techniques must be combined with knowledgeable instrument use, good common sense, and thorough documentation of work activities and inspection checkpoints to help ensure specification compliance. The amount of inspection and the specific inspection checkpoints will vary with the type and size of the coating project. This course presents eleven quality control inspection procedures as follows:

  • Pre-surface preparation inspection
  • Ambient conditions
  • Compressed air cleanliness
  • Surface profile
  • Surface cleanliness
  • Paint storage, mixing, and thinning procedures
  • Application techniques
  • Wet and dry coating thickness
  • Pinhole detection
  • Adhesion
  • Cure

 

This 3 PDH online course is applicable to engineers, design and construction personnel, and other technical professionals who are interested in gaining a better understanding of coating application and inspection.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Methods of coating application
  • Documentation of coating applications
  • Pre-surface preparation inspection
  • Measurement of ambient conditions
  • Assessment of compressed air cleanliness
  • Measurement of surface profile
  • Evaluation of surface cleanliness
  • Paint storage, mixing, and thinning
  • Measurement of wet coating thickness
  • Nondestructive measurement of dry coating thickness
  • Destructive measurement of dry coating thickness
  • Cleanliness and time (cure) between coats
  • Holiday/pinhole detection
  • Adhesion testing and evaluation
Course Document

In this professional engineering CEU course, you need to review Chapters 8 and 9 of the “Painting: New Construction and Maintenance” engineering manual, published by the United States Army of Corps of Engineers (USACE), Publication Number EM 1110-2-3400.

To view, print and study the course document, please click on the following link(s):
Coating Application and Inspection (111 KB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of fifteen (15) questions to earn 3 PDH credits. The quiz will be based on Chapters 8 and 9 of this USACE publication.
The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Corrosion: Overview
COURSE NO: H04-001
COURSE PROVIDER: Gilbert Gedeon, P.E.
Corrosion: Overview
Course Highlights

This online engineering PDH course provides basic information on the chemical interaction taking place during the corrosion process between the environment and the corroding metal. It also describes preventive measure to minimize or control the corrosion process.

 

Uncontrolled corrosion can cause many serious problems. Corrosion occurs continuously, and every metal in every facility is subject to some type of corrosion. Even though corrosion cannot be eliminated, it can be controlled.

 

This 4 PDH  online course is applicable to chemical and environmental engineers, design and construction personnel, technical staff and facility operators who are interested in gaining a better understanding of the theory of corrosion.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Corrosion theory
  • General corrosion
  • Crud and galvanic corrosion
  • Specialized corrosion
Course Document

In this professional engineering CEU course, you need to review Module 2, "Corrosion" of the Department of Energy Publication DOE-HDBK-1015/1-93, "Chemistry".

To view, print and study the course document, please click on the following link(s):
Corrosion - Overview (983 KB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of twenty (20) questions to earn 4 PDH credits. The quiz will be based on Module 2 of this DOE publication.

 

The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Engineering Ethics for Maryland Professional Engineers
COURSE NO: MD2-004
COURSE PROVIDER: Gilbert Gedeon, P.E.
Engineering Ethics for Maryland Professional Engineers
Note: This 2 PDH engineering ethics course is applicable only to Maryland Professional Engineers.
Accepted in:
Course Highlights

This online engineering PDH course presents the laws and rules of ethics and professional responsibility governing the practice of engineering in the State of Maryland. Excerpts from Title 14 of the Maryland Codes and Title 9, Subtitle 23 of the Maryland Regulations which relate to the rules of profession conduct, continuing education requirements, proper use of seal and other pertinent regulatory provisions are presented in this course.

 

Engineering ethics is (1) the study of moral issues and decisions confronting individuals and organizations involved in engineering and (2) the study of related questions about moral conduct, character, ideals and relationships of peoples and organizations involved in technological development (Martin and Schinzinger, Ethics in Engineering).

 

Since engineers are faced with frequent moral and ethical dilemmas while practicing their engineering profession, this course will provide you with moral and ethical guidance in your decision making process. Most importantly, it will provide you with insight on how to conduct, respect and protect your engineering practice with the utmost professionalism.

 

This 2 PDH online course is applicable to Professional Engineers licensed in the State of Maryland and who are required to demonstrate continuing professional competency in engineering ethics as a condition of their license renewal. For each renewal period, every licensee must complete sixteen (16) professional development hours, at least one of which must be relative to the rules of professional responsibility, conduct and ethics.
Learning Objectives

This PE continuing education engineering course is intended to provide you with the following specific knowledge and skills:

  • Overview of the laws and rules regulating the practice of engineering in the State of Maryland and their application to Professional Engineers
  • Understanding the roles of the Maryland Board as well as its disciplinary authority and disciplinary process
  • Learning about engineering ethics and the rules of professional conduct and responsibility
  • Understanding the continuing education requirements, proper use of seal and other pertinent provisions in the State of Maryland
  • Review of the disciplinary cases, range of violations and corresponding penalties imposed by the Maryland Board

 

Course Document
In this professional engineering CEU course, you need to review the course document titled “Engineering Ethics for Maryland Professional Engineers”.
To view, print and study the course document, please click on the following link(s):
Engineering Ethics for Maryland Professional Engineers (171 KB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of ten (10) questions to earn 2 PDH credits.The quiz will be based on the entire course document.
The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Structures and Properties of Metals
COURSE NO: T07-001
COURSE PROVIDER: Elie Tawil, P.E., LEED AP
Structures and Properties of Metals
Course Highlights

The online engineering PDH course addresses two aspects of metals. The first part of this course deals with the basic structures of metals and how those structures are affected by various processes. In addition, it contains information on the various imperfections and defects that the metal may sustain and how they affect the metal. The second part contains information on metal properties which are considered when selecting material for engineering design purposes. Each of these properties contains a discussion on how the property is affected and the metal's application.

 

This 7 PDH online course is applicable to structural and mechanical engineers, construction and design personnel, technical staff and facility operators who are interested in gaining a better understanding of the structures and properties of metals.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Understanding bonding
  • Learning about common lattice types
  • Understanding grain structure and boundary
  • Learning about polymorphism and alloys
  • Knowing the imperfection in metals
  • Learning about stress and strain and Young's
  • Modulus Understanding stress-strain relationship
  • Understanding the physical properties of materials
  • Learning about working metals and corrosion
  • Understanding hydrogen embrittlement
Course Document

In this professional engineering CEU course, you need to review Modules 1 and 2, "Structures and Property of Metals" of the Department of Energy Publication DOE-HDBK-1017/1-93, "Material Science".

To view, print and study the course document, please click on the following link(s):
Structures and Properties of Metal (1.46 MB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of thirty five (35) questions to earn 7 PDH credits. The quiz will be based on Modules 1 and 2 of this DOE publication.
The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

To buy the package , please click on: