Online Courses

Discount Packages

Ethics, Laws and Rules

Live Webinars

Video Presentations

Courses by Provider


CED Monthly

Subscribe and get 20% off

Your name:

Your e-mail:




FB Twitter LinkedIn

Delaware Materials and Ethics 24 PDH Discount Package

PACKAGE NO: DE24T-01
PACKAGE PDH: 24
PACKAGE PRICE: $288
To buy the package, please click on:
Courses in this Package
COURSE TITLE: Coating Application and Inspection
COURSE NO: T03-001
COURSE PROVIDER: Gilbert Gedeon, P.E.
Coating Application and Inspection
Course Highlights

This online engineering PDH course presents the technologies, techniques, advantages and limitations, equipment, typical coating types involved, and safety considerations for each type of application method.

 

The choice of an application method depends on the type of coating to be applied, the type and size of surface to be coated, and governing environmental regulations. There are various methods of coating application, including brush application, roller application, conventional spray, high volume-low pressure spray, airless spray, plural component spray, and electrostatic spray.

 

Approximately 85 percent of all premature coating failures are a result of poor surface preparation, inadequate mixing, thinning, and/or poor coating application. Onsite quality control inspection during surface preparation and coating application procedures can help prevent failures of these types. Proper inspection techniques must be combined with knowledgeable instrument use, good common sense, and thorough documentation of work activities and inspection checkpoints to help ensure specification compliance. The amount of inspection and the specific inspection checkpoints will vary with the type and size of the coating project. This course presents eleven quality control inspection procedures as follows:

  • Pre-surface preparation inspection
  • Ambient conditions
  • Compressed air cleanliness
  • Surface profile
  • Surface cleanliness
  • Paint storage, mixing, and thinning procedures
  • Application techniques
  • Wet and dry coating thickness
  • Pinhole detection
  • Adhesion
  • Cure

 

This 3 PDH online course is applicable to engineers, design and construction personnel, and other technical professionals who are interested in gaining a better understanding of coating application and inspection.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Methods of coating application
  • Documentation of coating applications
  • Pre-surface preparation inspection
  • Measurement of ambient conditions
  • Assessment of compressed air cleanliness
  • Measurement of surface profile
  • Evaluation of surface cleanliness
  • Paint storage, mixing, and thinning
  • Measurement of wet coating thickness
  • Nondestructive measurement of dry coating thickness
  • Destructive measurement of dry coating thickness
  • Cleanliness and time (cure) between coats
  • Holiday/pinhole detection
  • Adhesion testing and evaluation
Course Document

In this professional engineering CEU course, you need to review Chapters 8 and 9 of the “Painting: New Construction and Maintenance” engineering manual, published by the United States Army of Corps of Engineers (USACE), Publication Number EM 1110-2-3400.

To view, print and study the course document, please click on the following link(s):
Coating Application and Inspection (111 KB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of fifteen (15) questions to earn 3 PDH credits. The quiz will be based on Chapters 8 and 9 of this USACE publication.
The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Corrosion: Overview
COURSE NO: H04-001
COURSE PROVIDER: Gilbert Gedeon, P.E.
Corrosion: Overview
Course Highlights

This online engineering PDH course provides basic information on the chemical interaction taking place during the corrosion process between the environment and the corroding metal. It also describes preventive measure to minimize or control the corrosion process.

 

Uncontrolled corrosion can cause many serious problems. Corrosion occurs continuously, and every metal in every facility is subject to some type of corrosion. Even though corrosion cannot be eliminated, it can be controlled.

 

This 4 PDH  online course is applicable to chemical and environmental engineers, design and construction personnel, technical staff and facility operators who are interested in gaining a better understanding of the theory of corrosion.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Corrosion theory
  • General corrosion
  • Crud and galvanic corrosion
  • Specialized corrosion
Course Document

In this professional engineering CEU course, you need to review Module 2, "Corrosion" of the Department of Energy Publication DOE-HDBK-1015/1-93, "Chemistry".

To view, print and study the course document, please click on the following link(s):
Corrosion - Overview (983 KB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of twenty (20) questions to earn 4 PDH credits. The quiz will be based on Module 2 of this DOE publication.

 

The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Engineering Ethics for Delaware Professional Engineers
COURSE NO: DE3-002
COURSE PROVIDER: Gilbert Gedeon, P.E.
Engineering Ethics for Delaware Professional Engineers
Note: This 3 PDH engineering ethics course is only applicable to Delaware Professional Engineers. It is also offered as a recorded video presentation and as a live interactive webinar.
Accepted in:
Course Highlights

This online engineering PDH course presents the laws of professional responsibility governing the practice of engineering in the State of Delaware, as well as, the Delaware engineering code of ethics as follows:

  • Delaware Professional Engineers' Act: Title 24, Chapter 28
  • Delaware Engineering Code of Ethics

 

Engineering ethics is (1) the study of moral issues and decisions confronting individuals and organizations involved in engineering and (2) the study of related questions about moral conduct, character, ideals and relationships of peoples and organizations involved in technological development (Martin and Schinzinger, Ethics in Engineering).

 

This 3 PDH online course is applicable to Professional Engineers licensed in the State of Delaware and who are required to demonstrate continuing professional competency in engineering ethics as a condition of their license renewal. For each renewal period, every licensee must complete thirty (30) professional development hours (PDH) by June 30 of even years; 3 to 6 of which must be relative to engineering ethics or professional conduct and 9 of which may relate to project management or business skills. All other PDH's must be technical in nature and must relate to the licensee's area of practice.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Understanding the statutory laws regulating the practice of engineering in the State of Delaware and their application to professional engineers
  • Understanding the Delaware Engineering Code of Ethics promulgated by the Council of the DAPE to safeguard life, health and property and promote public welfare
  • Learning about the engineering rules of professional responsibility and ethical conduct as well as understanding the basic obligations of the engineer
  • Understanding the Delaware disciplinary process and the range of violations and corresponding penalties imposed by DAPE
Course Document

In this professional engineering CEU course, you need to review the course document titled “Engineering Ethics for Delaware Professional Engineers”.

To view, print and study the course document, please click on the following link(s):
Engineering Ethics for Delaware Professional Engineers (195 KB)
Course Quiz

Once you complete your course review, you need to take a multiple-choice quiz consisting of fifteen (15) questions to earn 3 PDH credits. The quiz will be based on the entire document.

The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Pre-Coating Surface Preparation
COURSE NO: T02-003
COURSE PROVIDER: Gilbert Gedeon, P.E.
Pre-Coating Surface Preparation
Course Highlights

This online engineering PDH course describes surface preparation standards, common methods of surface preparation, and abrasive type and selection methods.

 

Surface preparation is the key factor in determining the success of a protective coating system. The equipment and techniques that can be used to achieve the desired surface cleanliness and roughness (profile) vary considerably. Traditional methods of surface preparation are now accompanied by new, innovative methods that have evolved mainly because of the issues surrounding the safe removal of lead-containing coatings from industrial structures. The ultimate objective of surface preparation is to create proper adhesion of a coating over an underlying substrate.

 

This 2 PDH online course is applicable to engineers, design and construction personnel, and other technical professionals who are interested in gaining a better understanding of surface preparation prior to coating applications.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Common methods of surface preparation
  • Abrasive type and selection
  • Surface preparation standards and specifications
Course Document

In this professional engineering CEU course, you need to review Chapter 7 of the "Panting: New Construction and Maintenance" engineering manual, published by the United States Army of Corps of Engineers (USACE), Publication Number EM 1110-2-3400.

To view, print and study the course document, please click on the following link(s):
Pre-Coating Surface Preparation (159 KB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of twelve (12) questions to earn 2 PDH credits. The quiz will be based on Chapter 7 of this USACE publication.
The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Project Management for Engineering Professionals
COURSE NO: B05-001
Project Management for Engineering Professionals
Course Highlights

This online engineering PDH course presents an overview of modern practices in effective management of technical projects and engineering professionals’ participation in this process.

 

It starts with a discussion about the engineering personnel’s involvement in Project Management and definitions of the project, triple constraint and work breakdown structure. This is followed by the discussions of all major processes of Project Management, including:

  • Estimating
  • Scheduling
  • Definition of Scope
  • Procurement process
  • Risk management
  • Project communications
  • Project baseline and control
  • Performance measurement

 

Explanations are supported by numerous down-to-earth examples to improve the retention of material. The last part of the course covers one of the most effective methods of project control, Earned Value Analysis (EVA), showing participants how to use EVA metrics to forecast project outcome and define corrective actions, if needed. An extensive case study of EVA application is presented as well.

 

This 5 PDH online course is applicable to all engineering professionals looking to expand their knowledge and experience in modern project management to become a valuable member of their Project Team.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Understanding of engineering personnel involvement in the modern Project Management process
  • Knowledge of basic Project Management concepts
  • Learning how to use main tools and principles of modern Project Management to make you a valuable contributor into the overall project success

In addition, after completing this course, you'll be able to:

  • Describe the Project Engineer's involvement in Project Management
  • Provide a definition of the Project
  • List components of Triple Constraint
  • Know what WBS is for and how it is obtained
  • Understand the difference between effort and duration
  • Describe the main estimating techniques
  • List the types of Cost Estimates
  • Describe the views of a Project Schedule
  • List the project schedule optimization techniques
  • Define scope and scope "creep"
  • Describe the Project Engineer's involvement in a procurement process
  • List procurement options and types of contracts in technical projects; their advantages and disadvantages
  • Describe risk identification, analysis and response processes
  • List the main sources of Risk in utility company Projects
  • Describe the types of project communications
  • Explain how to make meetings productive
  • Define project baseline
  • List the main components of project control
  • Use Earned Value Analysis to forecast the Project outcome
Course Document

In this professional engineering CEU course, you need to review the course document titled, “Project Management for Engineering Professionals”.

To view, print and study the course document, please click on the following link(s):
Project Management for Engineering Professionals (382 KB)
Course Quiz
Once you complete your course review, you need to take a multiple choice quiz consisting of thirty five (35) questions to earn 5 PDH credits. The quiz will be based on the content of the course document.

 

The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

COURSE TITLE: Structures and Properties of Metals
COURSE NO: T07-001
COURSE PROVIDER: Elie Tawil, P.E., LEED AP
Structures and Properties of Metals
Course Highlights

The online engineering PDH course addresses two aspects of metals. The first part of this course deals with the basic structures of metals and how those structures are affected by various processes. In addition, it contains information on the various imperfections and defects that the metal may sustain and how they affect the metal. The second part contains information on metal properties which are considered when selecting material for engineering design purposes. Each of these properties contains a discussion on how the property is affected and the metal's application.

 

This 7 PDH online course is applicable to structural and mechanical engineers, construction and design personnel, technical staff and facility operators who are interested in gaining a better understanding of the structures and properties of metals.

Learning Objectives

This PE continuing education course is intended to provide you with the following specific knowledge and skills:

  • Understanding bonding
  • Learning about common lattice types
  • Understanding grain structure and boundary
  • Learning about polymorphism and alloys
  • Knowing the imperfection in metals
  • Learning about stress and strain and Young's
  • Modulus Understanding stress-strain relationship
  • Understanding the physical properties of materials
  • Learning about working metals and corrosion
  • Understanding hydrogen embrittlement
Course Document

In this professional engineering CEU course, you need to review Modules 1 and 2, "Structures and Property of Metals" of the Department of Energy Publication DOE-HDBK-1017/1-93, "Material Science".

To view, print and study the course document, please click on the following link(s):
Structures and Properties of Metal (1.46 MB)
Course Quiz
Once you complete your course review, you need to take a multiple-choice quiz consisting of thirty five (35) questions to earn 7 PDH credits. The quiz will be based on Modules 1 and 2 of this DOE publication.
The minimum passing score is 70%. There is no time limit on the quiz, and you can take it multiple times until you pass at no additional cost.
Certificate of Completion

Upon successful completion of the quiz, print your Certificate of Completion instantly. (Note: if you are paying by check or money order, you may print your Certificate of Completion after we receive your payment.) For your convenience, we will also email you your Certificate of Completion. Also, you can log in to your account at any time to access and print your Certificate of Completion.

To buy the package , please click on: